smaller we go..

New model is soon ready. But new shoes and new crank spindle is needed(WTF?!) When space is at it's minimum, nothing more than enough is acepted. Cycling shoes are ment to use for pedaling, not for walking or looking pretty in your feet. I'v allways been into minimalistic products in racing equipment and this is no exeption. Problem is that ther's no products available that follow this rule of mine (if we ignore Bont TT aero prototype). Custom made? exactly!

The actual model is now more aero but smaller inside. When you try to squeeze the model smaller, more demanding the inner use becomes, that's why shoes need to be reworked, and BB spindle. It looks allready too small to fit inside, hopefully it's not ;)
After few verifications, model is soon ready to be carved out from styrofoam.

New direction

Today I made a decision, model needs total updating, it must be more narrow up front, lower at middle and back. That means it will be longer and 300cm limit is a challenge, but I think I can make it. The result should be more efficient vehicle what it was previously. That ofcourse means that the current model will be ripped down completely, but I think this change is necessary. I will also trash my current BB and replace it with a narrow one.
Crank arms have a huge impact to the model, and because I dont see any good reason to go with really short arms due to my inseam lenght of 95cm, I will make it at least more narrow, that will have some impact on the nose area in both dimensions, height and widht by curving the shape differently. Trying to find a compromise between knee movement area, crank width and crank arm lenght. But because time is limiting variable, I will stick with the standard arms for now.

Round nose vs pointy nose

Finally I have a chance to do the tests that has allways bothered me. Round or pointy, hmm thats the question, not an easy answer though.

Both objects are identical exept nose area. Meaning of this is just to see how air acts around those two shapes. Enviromental settings are for both models: 20m/s air speed, surface roughness of 10um.
Force that moving air produces is shown in Newtons. Since air and its behaviour is scalable, object size is not relevant. Only magnitude of differencies rule in this study.

First, air is directional to objects Z-axis which is air direction. In this picture you are able to see pressure map of the objects. On round nose simulation high pressure area shows up in front, higher air drag is present. Sharp nose model has very moderate pressure area causing less drag. By numbers: sharp 0.5N, round 1.3N, so more than twice of force.



Next test is highly interesting. Side wind of 3m/s is present in axis Y and at the same time 20m/s air is moving in Z axis (direction of movement).
What happens now is that Z-axis directional force remains at level of 0.65N on sharp nose, and 1.6N on round nose. But when looking at the Y axis force, round nose gives a results of 0.44N and sharp gives 0.51N. Colors represent air velocity, scale is between 10 - 25 m/s.



So this tells us what was obvious, round shapes do help on sidewinds, but they cause lot of drag up front. Choosing right shapes could help to maximize efficiency in certain circumstances. This would mean that you should have shape to match every wind conditions, otherways you need to choose which parameters are most important for you, fast movement and less stability in windy conditions or, less fast but better stability. That allways leads into compromise. Whether you choose to run only 200 meters straight line in a calm weather, I'd go with the sharp one. When ride is longer say 6 hours and stability is required to match the enviromental changes, I'd go with something more round shape. Fact is that you can't have both in one packet.

Trike transformation

Next study is to test what would it mean to transform this object into three wheel concept. Model is transformed into trike with 2 front wheels and study calculates the drag change. Ther's two pictures, first shows the pressure map and the second shows the velocity map. Velocity plot is a planar cut from a certain distance above the ground where the turbulence caused by the front wheel is highly visible.





And the results, overall force of drag is in Newtons

single wheel(two wheel version) 1.3N
dual front wheel trike 3.5N

Differencies are significant, and probably this is not the best trike designs to think of.

Separating front wheels 40% more away from the body only increased the overall drag to 3.7N. But moving wheels closer to the nose decreased the drag dramatically. Final overall drag is now only 2.5N with object that looks like this.

Air drag testing with a nose

Since aerodynamics is an area where we dont bump into too often in our everyday life, it must be visualized by testing. Nose down, wide body, body height from the ground etc. all that has a meaning, so best thing is to test their influence and cut off the wings from guessing.
Here I made a study of nose behaviour in air drag. Model is very simple streamline object with ability to easy transformation of it's shape, specially it's height. You can see the model in here.



I tried to simulate what is the effect of the nose height in this model. Since my previous testing with some other models, small changes did not have effect too much to dramatically change the overall drag. Altering the nose height had very little effect to the rest of the model. So It is obvious that the nose itself did do most of the results and it's variations. Tests were made with full 3D part, with full 3D simulations, and artificial ground plane was present. Results here can be seen only in 2D for clarity.

Lets start with the lowest possible height. Without changing the lenght but changing the nose height, we can see steep attack angle in the nose area, specially in the upper part of the nose. More angle you have, more it looks like a flat area to the air causing air pressure to increase. Low nose caused very little of pressure under the body, but increased the nose pressure, so things are not in balance. We could keep the nose down and make that slope less steep by lenghtening the nose, or lowering the object, but since room is required for legs to pedal, that is impossible, and lenghtening would increase the surface area, and we dont want to do that either.



So we make the nose little higher. In this model the slope is divided into half, upper and lower portion are nearly in equal angle and the air cuts into half. Pressure area is the smallest and so is the drag. pressure under the body is moderate, and things looks like more balanced. Slightly more optimized shape in this part could give little more better results.



Third model is with high nose, the slope has moved to the bottom and forces air beneath the model. Increased pressure area and increased drag is present.



Now to the results, speed of the object is 20m/s. Lowest drag was present with the 2nd model, highest drag was with the 1st model, and after a certain point while lifting the nose, drag started to increase again. So with this model, the best place was when top and the bottom slopes were equal and drag increased when slopes were unequal.
Results with numbers, smaller number represents lower drag force in Newtons.

model drag nose height
-----------------------------------
1st 0,94299593 low
2nd 0,772091841 medium
3rd 0,838201198 high


Same object was used in the next study. Does a wheel in front change the previous results? This study shows that it did not. Results are in same direction as in previous one but naturally slightly bigger drag numbers.

Results with numbers, smaller number represents lower drag force in Newtons.

model drag nose height
-----------------------------------
1st 1,281011473 low
2nd 0,989317474 medium
3rd 1,033435136 high

Brick myth

I'v heard claims about aerodynamics of a brick stone, yep, brick stone has it's own aerodynamics ofcourse. Not sure who really needs this information unless you try to invent some new sport out of it.. But anyway, when there are urban legends, I put my Mythbusters hat on my head and try solve and prove it to be wrong, that's what Mythbuster-guys are doing, so lets play Adam and Jamie for a while ;D. The claim says, that brick with only tail fairing has less drag than the brick with only front fairing.

My goal is not to do tests and get actual accurate results of a brick stone and publish that on a science magazine, that is unnecessary, not even making a wind tunnel out of soda pills and some fancy strain gauges to measure forces what Jamie and Adam would do.
I try to just show the magnitude of the differencies, with simulation tools, someone else can do more precise tests if wants so.

Here's my brick with a sharp nose/tale, air speed is the same at both cases, only air direction is changed 180 deg. Simulations were run with 3D part, here only showing 2D picture as a reference.

Results are nearly what they were in the case of my previous hemisphere test. Flat face towards the wind gave over two times more drag than the sharp face towards the wind, with numbers 1,6N vs. 0,7N.
I'd say that the myth of "flat face towards has less drag", is busted :D

Hemisphere test >:-)

Since low aerodynamic drag is a base of movement in these vehicles, I will post my short study of 15 minutes. This study clearly shows the difference between flat surface vs round surface and reaction in air flow around them. Because the study is not done in scientific manners, I created basic shapes without any details or minor flluctuations on their surfaces, these results are not exactly true offcourse, just giving some quidance of this phenomenon.

The study contains a solid 50cm hemisphere, airflow is 10meters/s and surface is theoretically perfect with roughness of 0. Both hemispheres are equal, only variation is their air flow direction, the other is flat face to wind and the other is round face to wind. The results are: flat face to wind gave 13N of force and round face to wind gave 6N of force, so more than twice of force is generated when flat face is put towards the wind.



Previously made simulation with streamlined body (see previous posts) gave results 7N @ 20m/s, which is nearly the same as 50cm hemisphere but with double speed ! With equation F = ½ s v² A Cv , force of drag will give Cv value of 0.095 with given parameters. But frontal area needs to be rechecked in the process when, for example, the bubble is added. So there is a lot of variables and Cv value is not even close to it's practical and real value.

Mock Up

I totally forgot to show the mockup concept I worked during the summer. It is basically a 2x4 block of wood as a base with seat, BB-support and cranks attached to it. It's not a high tech unit, but it does basic things you need, all can be adjusted and get the quidelines of what can be expected on real thing. This mock up was later totally updated with bigger seat and frame curves along it's shape with accurate measurements which were transported to 3D-program. Previous 3d-model which was made with only few simple not accurate, quideline type of measurements, was totally foolish, and had a bit of a problem to solve it, I even felt "damn,this is going to be sh*t". But as so many times before, I had to think it fresly from the start, with the basics again, and I changed my sitting position closer to the ground and a bit more backwards and few other things and remeasured everything and squeeged all air out of it and shape became nice tube-like form and the overall shape was possible to make very streamlined, and I even got it more narrow and lower. And the most important thing is that I fit inside, into shape that looks impossible and ridicilously small, even unreal, but it's there.

It's funny to realize that only few measurements master the whole design, and there is not much you can do about it, form just pops out from you and your own body dimensions.

I concider myself lucky, and unlucky. For many sports size is not a benefical if it's on the bigger side, that is my problem, I'm on the wrong side. But to be big, at least you can do is to be narrow, and that's what I am. If one is big with wide shoulders and muscular upper body, I wonder what would the vehicle be like, wide for sure, and that is not optimum.

Computational Fluid Dynamics

Playing with my new toy, CFD-simulation tool. Just figuring out what are the things I should and can do, and what I should not even concider.
Because aerodynamics is a whole new world, and you could spend your whole life with searching the right shape, I just kept it simple and created the basic quidelines which to follow. Here is one of the samples I have tested. Forward directional force is aprx. 7 Newtons @ 20m/s, this model is without a bubble.

Wow, my weeks took longer than I expected ;-)

Hi, haven't been here for a while, strange, but that's how it goes. Project, that streamlined bike has not been buried, it's still going, going stronger and with determination, which has never been lost. The whole spring and summer went with training and traveling, skating hasn't been my main goal anymore, it's biking, and only biking. During spring and summer I'v done biking about 12 to 15 hours a week, and that pace should be kept up during wintertime. Only race I took part this year was TdH-2010, which I passed with 4:07, that included one crash and two technical problems, so I'm pretty satisfied for my result, and I'v done racebiking only twice this summer, mainly focusing on mountainbiking, so from that perspective I'm more than happy. MTB is well deserved change to sometimes boring straight paved roads.

Now, rainy weather is here to stay and forces me to stick inside and finally I have some time to put into this project. During summer I do have done something, more modeling, few more new softwares and CFD simultors and virtual wind tunnels have been tested, and some new parts designed including new set of wheels and rear suspension concept and put also some effort into "landing gear" which seems to be quite challenging task, not to mention some new electronics focused only for competition purposes, so lots of stuff in my head waiting to come out some day.
Now, more modeling, final shape is just there, on fingertips :D